L298N motor driver board module L298 for arduino stepper motor smart car robot 10pcs
L298N motor driver board module L298 for arduino stepper motor smart car robot 10pcs by Swiftflying at N Online Agency. Hurry! Limited time offer. Offer valid only while supplies last. Description: L298N is a high voltage, high current motor driver chip. The chip uses 15-pin package. The main features are: high voltage, maximum operating voltage up to 46V; output current, instantaneous peak current up to 3A, continuous operating current of 2A; rated power 25W. Contains two H-bridge high-voltage and high current full-bridge driver can be used to drive DC motors and stepper motors, relays, coils and other inductive load; using standard logic level signal control; having two
Product Description & Reviews
Description: L298N is a high voltage, high current motor driver chip. The chip uses 15-pin package. The main features are: high voltage, maximum operating voltage up to 46V; output current, instantaneous peak current up to 3A, continuous operating current of 2A; rated power 25W. Contains two H-bridge high-voltage and high current full-bridge driver can be used to drive DC motors and stepper motors, relays, coils and other inductive load; using standard logic level signal control; having two enable control terminal, in allows input signal without being affected or disable the device has a logic supply input, the internal logic circuit part of the work at a low voltage; can be an external sense resistor, the amount of change back to the control circuit. Drive motor using L298N chip, the chip can drive a two-phase stepper motors or four-phase stepper motor, can drive two DC motors. Note: 1. When you drive voltage (the figure identified as 12V input, can accept the actual input range is 7-12V) to 7V -12V, You can enable the on-board 5V logic supply, when using the onboard 5V power supply, interface + 5V Do not enter the power supply voltage, but can lead to 5V voltage for external use. (This is the routine use!) 2. When the drive voltage higher than 12V,equal to less than 24V (chip can support manual proposes to 35V, but in accordance with an 298 Conservative general inspection applications to 24V maximum voltage support has been very great! Time),such as to drive the rated voltage 18V motor. First, you must unplug the onboard 5V output enable jumper caps. And then 5V 5V output port External Access L298N internal voltage logic circuitry. (This is a high-voltage driver unconventional application)
Features & Highlights
- The module uses L298N chip as the main drive, with driving ability, low heat, anti-jamming features.
- It can be used to take power through the built-in 78M05 drive power part of the work, but in order to avoid damage to the regulator chip, when a drive voltage greater than 12V, please use an external 5V logic supply.
- Uses high-capacity filter capacitors, freewheeling diode protection, reliability can be improved.
Mounts & Accessories
3.94 x 3.15 x 5.91 inches
Have questions about this item, or would like to inquire about a custom or bulk order?
If you have any questions about this product by Swiftflying, contact us by completing and submitting the form below. If you are looking for a specif part number, please include it with your message.
Related Best Sellers
Feature:Material:316 Stainless Steel+plasticColor:silveryInput: 0-200 psi(Gauge Pressure)Output: 0.5-4.5VDCBrand Name:BQLZRPower:5VDCAccuracy: 0.5%FS~1%FSThread: 1/8NPTWorking Temperature: -40-+125ºCProtection:Reverse polarity protection,over-current protection,over-voltage protection,Anti interference designWorks for oil,fuel,diesel,gas,water or air pressure.Can be used in oil tank,gas tank,diesel tank etcWeight:54 gSize:5.3x2.5CM/2.08x0.98inch(HxD)good quality.
mpn: Ologymart5661608, ean: 0600161062529,
Features Efficient, easy to save, adjustable, simple and convenient.Long long bellows, easy to work.Fast cooling, large tuyere design.900ML large capacity watering can.ApplicationLatex paint.How to use?Drum installation1. Insert the straight head on the bellows into the body assembly and rotate it to the left.2. Insert the large connector on the bellows into the gun assembly and rotate it to the right.SprayingThe machine through the nozzle of the two ears rotating different positions, providing
mpn: Lejin-02, ean: 0749882497644,
Package Include: 1* Receiver (with cover) 2* Remote Control (with battery, If you need extra remote control , please tell us. ) Product Description 1. Working Voltage: DC12V-DC48V (DC 12V 14V 15V 16V 17V 18V 19V 20V 21V 22V 23V 24V 36V 48V All is ok) 2. Quiescent current:About 10ma 3. Working Temperature:-40'C- +80'C 4. Receiving Sensitivity :more than -108dBm 5.Working Frequency:315MHz/433MHz Optional by leaving us massage 6. Output 0V Switching Value use relay COM NO 7.Max Load Current:40A
By Muller Kueps
mpn: MKP608950, ean: 0013588056369,
Mueller-Kueps delivers high quality Spot Welding Drill Bits.. Specifics: High quality standard HSSE (High Speed Steel Cobalt alloyed). Best standard drill available. Double coated > HSSE-TICN (HSSE-Titanium Carbon Nitride). 1st PVD Titanium coating. 2nd Carbon Nitride finish. Highest cutting speed. Usable for interrupted cuts. Longest life time for best profitabilityExcentric Turn Chuck.